Military and Law Enforcement
We pruodly support our men and women in uniform
|Shipping Weight||2 lbs|
|Shipping Dimensions||12 x 6 x 3 in|
|Extended Length of Pull||
|Collapsed Length of Pull||
|Overall Extended Length||
|Overall Collaspsed Length||
1″ Fully Extended
Black, Flat Dark Earth
|Manufacturer Part Number||
The Magpul® MS4 QDM Sling includes factory installed heavy duty Magpul QDM quick-disconnect swivels. These swivels replace the push-button swivels found on most QD devices such as the MS4 Dual QD Sling Gen 2. With much easier single handed operation, the QDM swivels are also adapt at preventing rollover of the sling webbing. Quickly change between either one or two-point configurations.
Manufacturer Part Number: MAG953-BLK / MAG953-COY
Manufacturer Part Number: MSR-HAT
Made from 63% Polyester, 34% Cotton, 3% P.U. Spandex
Inspired by the ODIN Works O2 Lite, the XMR3 is the latest mag release available from ODIN Works. Machined from billet 6061 aluminum and designed to work with KNS pins and the BAD lever. The XMR3 has the largest profile yet, making it easily accessible by all shapes and sizes of hands and fingers. Works with both AR15 and AR10 lower receivers. Easy install that takes minutes.
-Compatible with BAD Lever. Will not work with anti-walk pins unless you modify the XMR2.
-Weight is just .1 oz (including paddle, button, and screws)
-Large surface area for quick magazine reloads.
-Easy to reach.
-Release magazine without changing grip or position.
-Contoured for positive depression and reduced slip.
Manufacturer Part Number: AAC-XMR3No Additional Information Provided
The Phase 5 Sloped Quick Disconnect End Plate (SQD-EP) was designed to replace the standard AR15/M4 carbine end plate. While still meeting the requirements of the original design, the SQD-EP is lighter and QD Swivel compatible.
Compatible with mil-spec carbine receiver extensions, commercial-spec receiver extensions, and all Phase 5 Pistol Buffer Tubes on nearly all AR15/M4/.308 AR Variant lower receivers. Lightweight and sturdy 7075-T6 billet aluminum construction is about 80% stronger than 6061-T6 aluminum.
Uses a standard AR15/M4 carbine Lower receiver extension castle nut (not included).
Accepts all push button QD swivels and QD slings.
QD mount is at a 30 Degree angle from the lower receiver to allow a 360 Degree rotation for ambidextrous use.
Lighter than the standard stamped steel receiver extension end plate (0.39 oz. vs 0.48 oz.)
The RA-535 Advanced Performance Trigger (APT) has a ridiculously fast reset, and minimal over-travel. Together with a smooth, crisp and light trigger pull, you will be firing quickly and more accurately. Quick and easy installation. (Includes free anti-rotation pins). Single-stage Trigger.
Manufacturer Part Number: RA-535No Additional Information Provided
Steel Core with Titanium Sleeve
Adds 1.52" inches to barrel
Includes crush washer
Anodizing colors vary as they are done manually. Color may dull after handling, use an ammonia based window cleaner to wipe it down and bring the color back.
Manufacturer Part Number: NoneNo Additional Information Provided
With the Stern Defense Mag-AD9 adapter, you can easily convert your AR-15 into an AR-9. Unlike other 9mm adapters, the Mag-AD9 is made from lightweight 6061 T6 aircraft grade aluminum which means it’s built for longevity and reliability. With premium features like last round bolt hold open (LRBHO) and an easy to reach mag release, the Stern Defense Mag-AD9 is the only choice for an AR9 conversion!
Manufacturer Part Number: MAGAD9 (001-SD MAG-AD9-GLOCK-9)
Although the MAG-AD9 works with many aftermarket magazines, Stern Defense recommends using post 2004 square notch, Glock OEM magazines, as these will provide the best fit and function.
Not compatible with PSA Hybrid or Foxtrot Mike bolts. This is due to the lug which strips a round off of the magazine being .035 of an inch further from center-line as compared to other bolt systems.
For the latest Guns, Gear, Reviews, Politics and Informational Videos, check out the The Daily Shooter on YouTube. Please help support our hard-working partner by clicking the Like and Subscribe buttons in the videos. View our collaboration videos HERE.
See what we're shouting about...